About Carlos Rico

This author has not yet filled in any details.
So far Carlos Rico has created 171 blog entries.
22 07, 2025

Application of Additive Manufacturing in the Comprehensive Development of a Cooling System for Roller Bearings in the Steel Industry

2026-10-15T10:41:32+00:00

Abstract This project addresses an inefficiency identified at the Avilés steelworks: the cooling of the roller bearings in the continuous sheet annealing line. Based on technical documentation, thermal imaging, sound pressure measurements and on-site observations, the causes of the problem and the requirements for a solution are identified, prioritizing effectiveness [...]

Application of Additive Manufacturing in the Comprehensive Development of a Cooling System for Roller Bearings in the Steel Industry2026-10-15T10:41:32+00:00
18 07, 2025

Analysis of the Dimensional and Geometrical Accuracy of Metal Parts Manufactured by Material Extrusion Additive Manufacturing

2026-10-29T11:44:52+00:00

Abstract Metal material extrusion (MEX/M) is an accessible alternative for manufacturing metal components, although its industrial application is constrained, among other factors, by the dimensional and geometrical accuracy achieved. This Final Degree Project was carried out within the framework of the AEMMEX research project, led by the EPMAN group at [...]

Analysis of the Dimensional and Geometrical Accuracy of Metal Parts Manufactured by Material Extrusion Additive Manufacturing2026-10-29T11:44:52+00:00
14 07, 2025

Areal Characterization of the Surface Topography of MEX-TRB/P Parts Using a Laser Line Triangulation Sensor

2026-10-29T11:50:12+00:00

Abstract This Final Degree Project investigates the areal characterisation of the surface topography of parts manufactured by thermoplastic material extrusion (MEX-TRB/P), using a laser line triangulation sensor to obtain three-dimensional surface data and analyse their relationship with printing parameters. Based on an experimental design involving PLA specimens, the influence of [...]

Areal Characterization of the Surface Topography of MEX-TRB/P Parts Using a Laser Line Triangulation Sensor2026-10-29T11:50:12+00:00
1 07, 2025

Optimized Extrusion Head for Metal Printing Using MEX/M

2026-10-20T14:43:59+00:00

Abstract In this project, the EPMAN group developed an extrusion head optimized for the additive manufacturing of metal/polymer composite filaments (MEX/M), addressing three critical aspects of the process: filament feeding, heating of the liquefaction chamber, and the geometric limitations of conventional nozzles. Alternative prototypes were designed and evaluated for each [...]

Optimized Extrusion Head for Metal Printing Using MEX/M2026-10-20T14:43:59+00:00
24 06, 2025

Topographical Analysis of MEX-TRB/P Parts Using a Laser Line Triangulation Sensor

2026-10-29T11:01:22+00:00

Abstract This Final Degree Project evaluates the feasibility of using a non-contact optical sensor based on laser-line triangulation to characterise the topography of parts manufactured by thermoplastic material extrusion (MEX-TRB/P). Integrated into a surface digitisation and analysis strategy, the system enables process-related features to be detected, over-extrusion and under-extrusion phenomena [...]

Topographical Analysis of MEX-TRB/P Parts Using a Laser Line Triangulation Sensor2026-10-29T11:01:22+00:00
12 06, 2025

Vibration Measurement in Additive Manufacturing Machines

2026-10-29T11:52:52+00:00

Abstract This project focuses on the development and validation of a vibration acquisition and analysis system for MEX (Material Extrusion) 3D printers, using MEMS (Microelectromechanical Systems) accelerometers and microcontrollers such as Arduino or ESP32. By implementing signal processing techniques, including the Fast Fourier Transform (FFT) in MATLAB, the project aims [...]

Vibration Measurement in Additive Manufacturing Machines2026-10-29T11:52:52+00:00
1 06, 2025

Optimization of the Printing and Debinding Processes in Parts Manufactured by MEX-TRB/M

2026-10-20T14:42:51+00:00

Abstract This project addressed the improvement of the quality of metal components manufactured using material extrusion with a metal-filled feedstock (MEX-TRB/M), an additive manufacturing technology notable for its low cost and accessibility. The work focused on the shaping and chemical debinding stages, analysing how part quality evolves from the green [...]

Optimization of the Printing and Debinding Processes in Parts Manufactured by MEX-TRB/M2026-10-20T14:42:51+00:00
27 11, 2024

Evaluation of Geometric Errors in Delta-Type Additive Manufacturing Machines

2026-10-29T11:02:59+00:00

Abstract This Final Degree Project addresses the evaluation of geometric errors in Delta-architecture additive manufacturing machines through the design, manufacture and measurement of metrological artefacts produced by the printer itself. Their characterisation using a coordinate measuring machine (CMM) enables deviations from the nominal models to be analysed in order to [...]

Evaluation of Geometric Errors in Delta-Type Additive Manufacturing Machines2026-10-29T11:02:59+00:00
2 09, 2024

Precision Engineering Applied to Additive Manufacturing

2026-10-29T12:54:57+00:00

Abstract The project aims to develop and optimize the additive manufacturing of metal parts using Metal Extrusion (MEX/M) as an alternative to conventional metal powder-based technologies, with the goal of reducing costs, energy consumption, and the risks associated with the handling of raw materials. The process uses filaments composed of [...]

Precision Engineering Applied to Additive Manufacturing2026-10-29T12:54:57+00:00
26 07, 2024

Design, Development and Validation of an Extrusion System for Bioprinters

2026-10-15T10:43:57+00:00

Abstract This project forms part of an European Horizon Europe project on the bioprinting of living cells for regenerative medicine. Its aim is to design an extruder capable of regenerating human skin directly on the patient (in situ bioprinting). It involves reviewing extrusion technologies for this application, the conceptual and [...]

Design, Development and Validation of an Extrusion System for Bioprinters2026-10-15T10:43:57+00:00
Go to Top