About Carlos Rico

This author has not yet filled in any details.
So far Carlos Rico has created 171 blog entries.
13 10, 2021

Layer contour characterization in additive manufacturing through image binarization

2026-10-13T16:45:17+00:00

Abstract On-Machine Measurement adoption will be key to dimensional and geometrical improvement of additively manufactured parts. One possible approach based on OMM aims at using digital images of manufactured layers to characterize actual contour deviations with respect to their theoretical profile. This strategy would also allow for in-process corrective actions. [...]

Layer contour characterization in additive manufacturing through image binarization2026-10-13T16:45:17+00:00
13 10, 2021

Validation of the Sandblasting Process in the Manufacturing of Precision Spheres for Non-Contact Metrology

2026-10-13T16:36:52+00:00

Abstract In order to ensure the measurements that can be made with non-contact metrology technologies, it is necessary to use verification and calibration procedures using precision artefacts as reference elements. In this environment, the need for increasingly accurate but also more cost-effective calibration artefacts is a clear demand in industry. [...]

Validation of the Sandblasting Process in the Manufacturing of Precision Spheres for Non-Contact Metrology2026-10-13T16:36:52+00:00
13 10, 2021

Feasibility analysis of using machinable glass ceramics to manufacture non-contact measurement approach metrological artefacts

2026-10-13T16:29:10+00:00

Abstract Rather than measurement contact methods, non-contact ones are more desirable in case of on-machine and in-process measurement due to their great accessibility and high acquisition rates. Nevertheless, it is well known that these methods commonly present different issues related to the surface properties of the digitized material and other [...]

Feasibility analysis of using machinable glass ceramics to manufacture non-contact measurement approach metrological artefacts2026-10-13T16:29:10+00:00
13 10, 2021

Digitization Methods of Grinding Pins for Technological Process Planning

2026-10-13T16:00:58+00:00

Abstract The paper presents different techniques for digitizing grinding pins and discusses the use of digitalized pins and the results of measurements in technological process planning (TPP), focusing on the challenges of the digital era. It describes the potential of different measuring devices, taking into account the digitization of a [...]

Digitization Methods of Grinding Pins for Technological Process Planning2026-10-13T16:00:58+00:00
23 07, 2021

Design of an Automated Storage and Traceability System for Additive Manufacturing

2026-10-15T13:57:51+00:00

Abstract This project updates the design of TRAC3D, an automated part storage system associated with Triditive's AMCELL mass additive manufacturing machine, in which multiple printing arms operate within an enclosed chamber. The aim is to automate the storage and traceability of manufactured parts, enabling additive manufacturing production to scale up [...]

Design of an Automated Storage and Traceability System for Additive Manufacturing2026-10-15T13:57:51+00:00
22 07, 2021

Artefacts for volumetric error determination on additive manufacturing machines: a case study

2026-10-08T16:47:26+00:00

Abstract In this Project, the feasibility of using artefacts manufactured using additive manufacturing techniques to determine the geometric errors of the machines themselves has been analysed. To this end, a procedure for determining these errors was developed and applied to a real case study. The review of the state of [...]

Artefacts for volumetric error determination on additive manufacturing machines: a case study2026-10-08T16:47:26+00:00
8 07, 2021

Study of the dimensional and geometrical accuracy of parts manufactured by FFF on a test bench

2026-10-15T19:11:32+00:00

Abstract In this project, cubic and cylindrical parts were manufactured using two FFF (Fused Filament Fabrication) machines: a BCN3D machine and a test bench developed by IPF. The work was structured into two phases: the first focused on selecting and adjusting the manufacturing parameters through visual and metrological inspection of [...]

Study of the dimensional and geometrical accuracy of parts manufactured by FFF on a test bench2026-10-15T19:11:32+00:00
1 07, 2021

Design and Development of a Recoating System for Metal Powder 3D Printing

2026-10-15T13:59:57+00:00

Abstract This project was carried out at Triditive, which aimed to incorporate an additional 3D printing method for metallic materials. It focuses on the design and development of the powder recoating system (the mechanism for spreading powder layers) for a Binder Jetting machine, a process in which a binding agent [...]

Design and Development of a Recoating System for Metal Powder 3D Printing2026-10-15T13:59:57+00:00
28 07, 2020

Two-dimensional layer contours digitising of parts manufactured by FFF

2026-10-26T19:03:38+00:00

Abstract Based on the results obtained, it can be concluded that the choice of the parameters (M), (T) and (S_f) significantly affects the quality of the detected contours, and that their optimal combination depends on the algorithm used and the characteristics of the image. The contrast between the target layer [...]

Two-dimensional layer contours digitising of parts manufactured by FFF2026-10-26T19:03:38+00:00
24 07, 2020

On-machine monitoring applied to additive manufacturing processes

2026-10-29T12:06:44+00:00

Abstract The objective of this project was to develop and implement a procedure for validating finite element simulations applied to the Laser Metal Deposition using powder (LMD Powder) Additive Manufacturing process. An experimental methodology was designed, covering the study of LMD Powder technology, experimental setup, model calibration, and final validation. [...]

On-machine monitoring applied to additive manufacturing processes2026-10-29T12:06:44+00:00
Go to Top