About Carlos Rico

This author has not yet filled in any details.
So far Carlos Rico has created 171 blog entries.
20 10, 2026

Multi-stage Characterization of Metal Parts Produced by Material Extrusion Additive Manufacturing (CAFAMEX)

2026-10-23T08:52:51+00:00

Abstract The CAFAMEX project investigates the additive manufacturing of metal components using material extrusion of a thermoplastic feedstock loaded with metal particles (MEX-TRB/M). This technology enables the production of metal parts using equipment that is less costly and less complex than that required by other metal additive manufacturing processes. The [...]

Multi-stage Characterization of Metal Parts Produced by Material Extrusion Additive Manufacturing (CAFAMEX)2026-10-23T08:52:51+00:00
13 10, 2026

Surface quality comparison in MEX/P manufactured parts across different machines and process parameters

2026-10-13T15:50:11+00:00

Abstract This study investigates the influence of machine selection and process parameters on the surface roughness (Ra) of parts manufactured using an Anycubic Vyper, an Ultimaker S5, and a custom-built test bench. Specimens measuring 40 × 40 × 10 mm were fabricated using a Design of Experiments (DoE) approach, varying [...]

Surface quality comparison in MEX/P manufactured parts across different machines and process parameters2026-10-13T15:50:11+00:00
13 10, 2026

Comparative analysis of Fused Deposition Modelling (MEX-TRB) printed parts using Al2O3 versus PLA

2026-10-13T15:43:34+00:00

Abstract This study compares the accuracy and resolution of parts fabricated by fused deposition modeling (FDM) using 100 vol% polylactic acid (PLA) filaments and ceramic filaments containing 45 vol% Al₂O₃ and 55 vol% polyolefin binder. Test artifacts were manufactured and evaluated according to ISO 52902:2023. Dimensional accuracy was assessed along [...]

Comparative analysis of Fused Deposition Modelling (MEX-TRB) printed parts using Al2O3 versus PLA2026-10-13T15:43:34+00:00
13 10, 2026

Feasibility of non-contact digitizing for topography characterization of MEX/P parts

2026-10-13T15:35:07+00:00

Abstract This study evaluates two non-contact sensors for characterizing the surface topography of parts manufactured by Material Extrusion of Polymers (MEX/P): a ConoPoint-10 conoscopic holography sensor (CH) and a Gocator 2410 laser line profile sensor (LTS). Seven 40 × 40 × 10 mm prismatic specimens made from different technical-grade polymers [...]

Feasibility of non-contact digitizing for topography characterization of MEX/P parts2026-10-13T15:35:07+00:00
13 10, 2026

Surface Reconstruction Quality with Apple’s TrueDepth Sensor: Impact of the Stand-Off Distance

2026-10-13T15:27:40+00:00

Abstract This study evaluates the geometric accuracy of point clouds acquired with Apple’s TrueDepth sensor, focusing on the influence of sensor-to-object distance. Tests were conducted using Necuron 651 polyurethane specimens featuring a flat surface, two parallel planes, and a hemisphere. A semi-automated test bench enabled digitization at different stand-off distances. [...]

Surface Reconstruction Quality with Apple’s TrueDepth Sensor: Impact of the Stand-Off Distance2026-10-13T15:27:40+00:00
7 10, 2026

Research stay at the Università degli Studi di Perugia (Italy)

2026-10-29T15:25:37+00:00

Between September and December 2026, Dr. Fernando Peña, a researcher in the EPMAN Research Group, is undertaking a research stay at the Smart Manufacturing Laboratory of the Università degli Studi di Perugia (Italy). This research mobility is funded by the 2024 José Castillejo Grants for Mobility Stays Abroad for Young [...]

Research stay at the Università degli Studi di Perugia (Italy)2026-10-29T15:25:37+00:00
1 10, 2026

Test Bench

2026-10-01T11:37:21+00:00

Sensorized MEX/M test bench for manufacturing test parts and monitoring the printing process through real-time and layerwise data acquisition. Print Technology: MEX-TRB/P and MEX-TRB/M Build Volume: 230 x 230 x 110 mm Inspection Volume: 380 x 1050 x 110 mm (approx.) In-situ monitoring with real-time process sensing and layer-by-layer scanning [...]

Test Bench2026-10-01T11:37:21+00:00
1 10, 2026

Test Bench

2026-10-26T15:42:56+00:00

Sensorized MEX/M test bench for manufacturing test parts and monitoring the printing process through real-time and layerwise data acquisition. Print Technology: MEX-TRB/P and MEX-TRB/M Build Volume: 230 x 230 x 110 mm Inspection Volume: 380 x 1050 x 110 mm (approx.) In-situ monitoring with real-time process sensing and layer-by-layer scanning [...]

Test Bench2026-10-26T15:42:56+00:00
30 09, 2026

3D Printer

2026-09-30T16:03:06+00:00

Professional dual-extruder 3D printers for high-precision production and rapid prototyping, featuring large build volumes, high-speed printing, automatic bed leveling, modular extruders, and remote monitoring via RaiseCloud. Print Technology: MEX-P and MEX-M Build Volume: 300 × 300 × 300 mm (Pro3) / 300 × 300 × 605 mm (Pro3 Plus) Print [...]

3D Printer2026-09-30T16:03:06+00:00
29 09, 2026

3D Printer

2026-10-20T17:40:39+00:00

3D printer using FFF/FDM technology, primarily designed for high-temperature engineering materials, especially PEEK and its reinforced variants. Print Technology: MEX-P Build volume: 260 × 260 × 260 mm Materials: PEEK, PEEK-CF, PEEK-GF, PEKK, PPS, PPA-CF, PA12-CF, PA6/66, PC, ABS, ASA, PLA and other engineering-grade thermoplastics Layer resolution: Up to 50 [...]

3D Printer2026-10-20T17:40:39+00:00
Go to Top